Order now and get your letters (in Israel) in a week!
|
Size options: |
|||
| Size | Height of letter Bet | Numbers’ height | |
| M | 10.5 cm (4.1″) | 11.9 cm (4.7″) | |
| L | 17 cm (6.7″) | 19.3 cm (7.6″) | |
Metal Hebrew Letters | Dark Brass | 2 Large Sizes| Modern Light Font – Order here!
₪75.00 – ₪129.00
Metal Hebrew letters in dark Brass
- Material: Brass 1.5 mm thick
- Finish: Chemical Patina darkening
- Color: Dark Brown
- Weatherproof: It doesn’t rust, nor the color changes
Options to choose from:
2 Sizes: M, L
4 Mounting options:
1) Plain, no holes, for glue mounting
2) Two holes & screws for wooden or metal door / fence
3) Two holes, screws and plugs for wall mounting
4) Double-sided adhesive Scotch 3M glued to the back of the letters
Darkened Brass
These metal Hebrew letters are made of natural brass that has undergone a process of natural blackening through prolonged absorption with a special chemical. The resulting color is an uneven dark brown, as can be seen in the product photos.
What size is right for me?
If you are undecided send Ugo a picture of the place for assembly that includes dimensions. Please take a picture from the front – not from the side. We will prepare a computer simulation and then we will know what font size is most suitable for your project. Ugo’s WhatsApp: 050-5800120
How to mount the letters
Preparation
- Mark a line on the wall / door with a pencil or masking tape
- Mark the center of the text line
- Start mounting the letters from the center to the right, and from the center to the left
Gluing
For gluing the metal Hebrew letters we recommend using “Super 7” or “Super 7 Hi-Tack” silicone glue (stronger).
- Place the glue on the back of the letter, only in the wider areas of it. Put in a generous amount but be careful not too much that the glue does not slide off the side when sticking to the surface.
- Place the letter in place and press it gently. For a few seconds after clicking, you can still reposition the letter (a few millimeters) to align it with the line of text.
- Do not touch the letters for at least 12 hours. When the weather is particularly hot it is recommended to perform the gluing with silicone glue in the evening.
Gluing on stone:
In addition to silicone glue, marble glue can be used, which is an epoxy glue. In this case it is advisable to search for a professional with experience in this type of work.
Mounting the metal Hebrew letters with screws
- Set the letter in its proper place on the door
- Mark with a pencil (through the holes) a mark on the door and then remove the letter
Wooden door / fence: Screw the screw up to about half its length, then screw it back out
Steel door / fence: Drill small holes in the points you marked. Use a 2 mm diameter “metal-wood” drill bit - Set the signal back in place and screw the screws to the door / fence through the letter
Warning: Be careful that the screwdriver does not “escape” and scratch the letter!
In addition, it is recommended to use latex gloves to avoid leaving fingerprints on the metal. In such case remove them with a little vinegar on a soft cloth.
Adding backside spacers
On the back of the letters you can add nuts 1 cm in size and 5 mm thick. If you plan to add spacers, select “Two holes & screws” as mounting option when filling the order form.
In one of the photos in this post you can see what is the recommended location for installing the rear nut on each letter and number.
To glue the nuts on the back of the letters it is recommended to use “Super 7” glue.
The nuts that will be mounted corresponding to the holes do not require gluing because the screw passes through them.
Note: Do not stick a nut too close to the edge of the letter, always leave a space of at least 5 mm.
Need Brass numbers & Hebrew letters in custom design?
Order here
Cutting metal letters:
